Powered by Mr. Cheto ElectricText for serviceReal Southern California work
Watch actual Southern California service calls—from the original problem and professional diagnosis to the completed repair and verified result.
Real job video proof
Real Southern California field work connected to the problem, location and service—not vague promises.
Solar Wholesale Group dispatched Eco Solar & Electric to a Laguna Niguel home for an approved Enphase microinverter replacement. This field video documents safe tile-roof access, the affected module and under-module equipment, replacement work, the Enphase combiner and the serial-number handoff used to retire the old device and commission the replacement in the existing monitored system.
PMI Patron called Eco Solar & Electric for a solar system at a managed multifamily property in Signal Hill. The SunPower inverter reported that the grid was missing. Field testing traced the condition to the 20-amp solar backfeed breaker, which was off and not fully seated in the panel. We reseated the breaker, restored the AC connection and verified the system operating again before documenting the result for the property manager.
This Palos Verdes Estates homeowner found Eco Solar & Electric through Google, reviewed our customer feedback and website, then called us directly. Her service call involved two legacy Aurora inverters: one operating and one reporting E031. The manufacturer identifies E031 as an internal error involving voltage measured at the output relay. We compared the paired equipment, verified the AC supply, checked the DC array inputs and followed a controlled restart before documenting the repair and replacement path.
A rental-property facelift included replacing outdated receptacles and switches with clean, updated devices. This real project video shows the finished rooms, device replacement work and final details that help a refreshed property look complete while keeping the electrical scope professionally handled.
During Southern California heat, this Bellflower bedroom received a ceiling fan with integrated LED lighting and remote controls. The video shows assembly, installation and the completed fan operating at the finished location.
The original SolarEdge installer was no longer available and the monitoring connection was not dependable over Wi-Fi. This real Glendora service video shows the communication section opened, an eight-conductor Ethernet connection terminated, SolarEdge monitoring changed to Ethernet and the hardwired communication path configured.
At this commercial bank, critical IT equipment and its UPS were exposed to a reported 2–6 second interruption while three EG4 12000XP inverters transferred between utility and battery power. This field video documents the system, the operational stakes and our diagnostic assessment; it does not claim that the final correction has already been completed.
This Rinnai tankless water heater still required dependable 120-volt power for its controls and operation. The documented installation shows a new dedicated 20-amp branch circuit using #12 copper conductors, GFCI protection where applicable and final electrical testing instead of sharing an existing appliance circuit.
The breaker kept tripping when multiple loads were in use. We traced the affected circuit, found that it was carrying more than it should and planned the kitchen and air-conditioning loads around properly separated circuits. The video shows the symptom and field diagnosis.
The existing bathroom fan created the appearance of ventilation, but it did not have a proper exhaust path to the exterior. We opened the affected route, installed a dedicated duct through the attic and completed an exterior termination so moisture and odors could leave the home as intended.
The Powerwall monitoring wiring and current-sensor orientation had been installed backward. We traced the power-flow signals, corrected the wiring direction and restored accurate solar, home, battery and grid monitoring.
We evaluated a Powerwall 3 solar shutdown problem by testing the photovoltaic strings and mid-circuit interrupter paths. This methodical process helps distinguish an MCI issue from conductor, connector or other solar-array faults.
A stairway three-way smart-lighting system was not operating correctly. We troubleshot the Lutron RadioRA 2 controls, restored operation and verified control from both the upper and lower locations.
Inside this four-story Venice Canals home, a compact Siemens panel was carrying major loads from an elevator, large central air-conditioning equipment and Level 2 EV charging. We evaluated the burning-smell and overheating condition before it could escalate into an electrical fire.
Watch documented field work from an Eco Solar & Electric project in Huntington Beach. This project page connects the real job video with our licensed electrical, solar and energy-system service in coastal Orange County.
Problem: the homeowner needed faster, dependable home charging instead of relying on slower charging options. Solution: we evaluated the electrical capacity, installed a dedicated Level 2 circuit and connected and verified the Tesla Wall Connector.
Problem: both SMA Sunny Boy inverters on this ground-mounted solar system were no longer producing power. Solution: we diagnosed the inverter and array conditions, documented the failure and provided a favorable replacement path to restore reliable solar production and modern monitoring.
Field experience
See how we approach electrical, solar, battery, EV-charging and everyday property upgrades before choosing who will work on your property.
Visit Eco Solar & Electric on YouTube ↗Ready when the problem isn’t.
Call, text a photo or send a short description. We’ll help identify the right next step.